Pages

Wednesday, December 1, 2010

DIY How to Carbon Fiber Tubes & piping for Intakes how to



This second part covers a lot of ground but the techniques can be used for complex 
projects. To demonstrate how to make a two part mold I’ve decided to mold a tube which 
could be use to make charge pipes, etc. 

All the usual disclaimers_the chemicals are hazardous so use adequate protection. This 
tutorial is how I do it. There are other methods which may be superior. If you choose to 
try these procedures its at your own risk. 

First I wax the part thoroughly will mold release wax. I put on at least six coats. Wait till 
each coat dries and buff.  I use clay to form my parting lines along with foam 

board. 

I cut the clay into long strips which will be applied to the 
part. 

This is followed by the foam board which is pressed firmly against the clay and the back 
size is hot glued to the part. Important is the parting line is placed on each center line of the tube.

CLICK READ MORE TO VIEW THE REST


This is repeated on both sides. I also use plastic half rounds as registration aids. I bought 
these from a sewing fabric store.


I also add extra pieces of foam board to the glue side and glue these on to further support the flanges

The flanges are waxed on the side to be molded and also sprayed with PVA. Once its all dry its time to apply the gel coat.

I use an orange tooling gel coat for my molds.

I apply this in two coats to about 1/16 inch thick and allow to dry to fingerprint dry 
state. Its then time to start laying on the fiberglass. I use chopped fiber for the tight places 
and around the plastic buttons.



The part after six layers of 6oz. Cloth and allowed to dry. The next step is to flip it over 
and remove the foam board support and flanges and clay. Pop out the plastic 
buttons.

Don’t loosen the metal tube. Now wax the tube and flanges with six coates of wax and 
PVA. Repeat laying on two coats of gel coat followed by the fiberglass.

Let everything harden overnight and use wedges(Bondo spreaders work great) to separate.



Remove the tube, wash off the PVA with water and then wax the mold. Note how the 
plastic rounds allow perfect alignment. This step is only necessary for tube. You need to 
form an inner flange to allow the final tube halves to be bonded.  
Take one half and replace the tube and wax everything again. Lay fiberglass over the 
flange and about 1” over the tube. You only nee two layers of cloth here. Note –I’ve drilled ¼” holes through the flange.



Once dry, remove the tube and trim the raw edges to about ¾” wide.


This is the tricky part. You need to decide how many layers of CF you will be using to 
lay up the tube. I usually use three.Cut three strips just as wide as the lip ~ ¾” and use resin to bond these to the lip. 
Now use the same process to make another lip for the other side of the mold.
Bolt the lip to the mold half. Again wax and buff. Begin laying down a layer of resin 
followed by a layer of CF. I used fiberglass to backup the CF just to save materials for this demo.




Be sure the resin and material fits well where the mold and lip come together. Once dry 
trim. If you time it before everything completely drys you can trim with a razor blade.



You can now sand the lips on each finished piece and bond together with resin or use an 
epoxy glue for strength. A better way which everything in perfect alignment is to 
unscrew the lips from the flanges. Wax the mold and replace the CF half tubes. Run a 
small amount of resin along the lips and then clamp the two mold halves together. I then 
saturate fiberglass tape and place the tape over the inside lips to strengthen.



This is what it looks like after drying. A few coats of urethane and you have a perfectly round, extremely strong tube. Actually we tested this tube with an 180 lb. onlooker standing on it and it didn’t deform or separate.  I used this same technique to make a charge pipe for a Honda we were turboing. 



I’m also using a bit different technique to make seamless tubes using CF sleeves and an 
inflatable blader. 
I hope this helps with your future project.  



33 comments:

  1. great blog!!! this post is ...very nice
    love your style...
    follow u
    xx
    =P

    ReplyDelete
  2. pictures arent loading for this any more :'( anyway that can be fixed? or is it just my computer

    ReplyDelete
  3. What can I use to make a bladder mould for 4" round intake?

    ReplyDelete
  4. Diffusers are usually applied in enclosed areas that have flat ceilings and walls that are parallel to each other. Acoustics Cyprus

    ReplyDelete
  5. I found your blog on Google and read a few of your other posts. I just added you to my Google News Reader. You can also visit Alloy Steel Fittings for more Metallect Steel Industries related information and knowledge, Keep up the great work Look forward to reading more from you in the future.

    ReplyDelete
  6. Hand tools range from general tools to specific tools. Some of them include automatic center punch for making a dimple in a work piece; chisel for carving wood, stone, or metal; clamp for securing objects tightly together; pliers for gripping objects with the use of leverage; and more. Composite Mould Release

    ReplyDelete
  7. Thank you for taking the time to publish this information very useful! Plombier Paris 24/24

    ReplyDelete
  8. Thanks for sharing that blog with us. If anyone here searching uns s31803 pipe then visit Perfect Impex.

    ReplyDelete
  9. Netter Post! Dies ist ein sehr schöner Blog, auf den ich dieses Jahr definitiv mehrmals zurückkommen werde! Vielen Dank für den informativen Beitrag. rohrreinigung münchen

    ReplyDelete
  10. Ideal for first light and sunset cosmology. Hispeed Laser

    ReplyDelete
  11. After read this post I understand new things and Knowledge of this. Phosphor Bronze Round Bar

    ReplyDelete
  12. our contents are completely awesome and share worthy. Monel 400 Bar

    ReplyDelete
  13. This comment has been removed by the author.

    ReplyDelete
  14. This comment has been removed by the author.

    ReplyDelete
  15. This post loaded with lots of useful information. Keep it up. Stainless Steel 316 Flanges

    ReplyDelete
  16. Hello it’s truly a good for me to visit this web page, I love your content Inconel 600 Pipe Fittings

    ReplyDelete
  17. Keep sharing these types of information, that All suggestions in your blog is helpful for us. Monel 400 Plates

    ReplyDelete
  18. This comment has been removed by the author.

    ReplyDelete
  19. I found your blog on Google and read a few of your other posts Hastelloy C22 Plate

    ReplyDelete
  20. After read this post I understand new things and Knowledge of this. Phosphor Bronze Bar

    ReplyDelete
  21. This is a great article with lots of informative resources. Unifit Fasteners

    ReplyDelete
  22. Very Nice Article...Good Information..Thanks for sharing. Ubique Alloys

    ReplyDelete
  23. This comment has been removed by the author.

    ReplyDelete
  24. This comment has been removed by the author.

    ReplyDelete
  25. Your contents are completely awesome and share worthy. Aleacion Tubos

    ReplyDelete
  26. Thanks for your marvelous posting! I really enjoyed reading it. Pleca Hoja

    ReplyDelete
  27. I found your blog on Google and read a few of your other posts. I just added you to my Google News Reader. You can also visit duplex plate suppliers for more Siddhagiri Metals & Tubes related information.

    ReplyDelete
  28. Hi there, I read your blogs on a regular basis. Very Nice, keep it up!  Nandini Steel

    ReplyDelete
  29. So as a client you don't have to stress over being liable for a plumber having a mishap while working in your home.
    piping

    ReplyDelete